The PCN3TJ00F from Sharp is a 4 pin, mini flat general purpose photocoupler. This photocoupler contains an IRED optically coupled to a phototransistor. Tel: Fax: / http://www. Photocoupler. Product Data Sheet. LTVT. Spec No. A/PG Page 2 of 8. Mini-flat Package General Purpose Photo Couple. KPCNT. Absolute Maximum Ratings (Ta=25 °C).
|Published (Last):||1 December 2004|
|PDF File Size:||2.96 Mb|
|ePub File Size:||3.69 Mb|
|Price:||Free* [*Free Regsitration Required]|
Photocoupler 1-CH Transistor Mini-Flat
Sending feedback, please wait Geert Van Droogenbroeck on November 18, at Hi, The MOC, is a phototriac coupler, meaning that instead of the phototransistor, it has a phototriac, which is basically a triac with the gate driven by the LED. Save to parts list Save to parts list.
If the LED is good then we should check the phototransistor, you could measure it with the ohmmeter just like the LED between pins 3 and 4 the emitter and collectorand you should get a high resistance value both ways if the phototransistor is good. Wade on February 5, at 9: Each On a Reel of Leave a Reply Cancel reply Your email address will not be published.
Buy Optocouplers with 4-Pin Pins | eBay
But what i want to mention is there is a different testing circuit on the datasheet of H11B1. Shahid on August 7, at 1: You helped me understand how to use a tester on a optocoupler Thanks. Each In a Pack of Hi, Both methods are correct. Mihai on June 10, at Save to an existing parts list Save to a new parts list. You agree that the Information as provided here through an intermediary may not be error-free, accurate or up-to-date and that it is not advice.
The firehose by day and forty photocouoler by night, An engineer may never sleep and still be just as bright. Your email address will not be published. Good design photocouupler as little design as possible.
Thank you for your feedback. Please correct the pin numbers in image. It depends on the 2nd circuit you are supplying the voltage on collector of the optocoupler, optocoupler will never transfer the voltages of circuit1 to circuit2, it decreases resistance between your supplied voltages at collector and emitter on the input of circuit2.
PCN7JF Sharp | Photocoupler 1-CH Transistor Mini-Flat | | RS Components
Mihai on February 6, at Thank you for the information. If you get a value either way or no value at all, then certainly there is a problem with the LED, and you should find another optocoupler.
The LED is basically a diode, and it should not conduct both ways not get values on the meter both ways. I use analog ohmmeter with 2 internal batteries, 3V to turn on LED pins 1 and 2and photocooupler V-metar on diode tester mode on transistor side. Save to parts list Save to parts list.
The purpose of an optocoupler is to transfer signals from one circuit to another yet keep them galvanically isolated. You agree that photocuopler Information as provided here by RS may 3557 be error-free, accurate or up-to-date and that it is not advice. Mihai on November 20, at 1: Evis on November 12, at 7: Hi, maybe a stupid question: The Manufacturers and RS reserve the right to change this Information at any time without notice.
You have chosen to save the following item to a parts list:. Please enter a message. Hi, First of all thanks for sharing such an useful information.
Mihai on September 17, at Sarfaraz on November 8, at 9: Arvind Vijaykumar on June 1, at The alcohol never solved anything, but neither did water or milk. Nupra on March 18, at 6: Ado on November 14, at Better check the datasheet for a test circuit. The nice thing about standards is that you have so many to choose from.